Convert binary and hex values to ascii
The binascii module contains a number of methods to convert between binary and various ASCII-encoded binary representations. Normally, you will not use these functions directly but use wrapper modules like uubase64or binhex instead.
The binascii module contains low-level functions written in C for greater speed that are used by the higher-level modules. The binascii module defines the following functions:. Convert a single line of uuencoded data back to binary and return the binary data. Lines normally contain 45 binary bytes, except for the last line. Line data may be followed by whitespace. Convert binary data to a line of ASCII characters, the return value is the converted line, including a newline char. The length of data should be at most Convert a block of base64 data back to binary and return the binary data.
More than one line may be passed at a time. The return value is the converted line, including a newline char. The newline is added because the original use case for this function was to feed it a series of 57 byte input lines to get output lines that conform to the MIME-base64 standard. Otherwise the output conforms to RFC Convert a block of quoted-printable data back to binary and return the binary data.
If the optional argument header is present and true, underscores will be decoded as spaces. The return value is the converted line s.
If the optional argument quotetabs is present and true, all tabs and spaces will convert binary and hex values to ascii encoded. If the optional argument istext is convert binary and hex values to ascii and true, newlines are not encoded but trailing whitespace will be encoded.
If the optional argument header is present and true, spaces will be encoded as underscores per RFC If the optional argument header is present and false, newline characters will be encoded as well; otherwise linefeed conversion might corrupt the binary data stream.
The string should contain convert binary and hex values to ascii complete number of binary bytes, or in case of the last portion of the binhex4 data have the remaining bits zero. Perform RLE-decompression on the data, as per the binhex4 standard.
The algorithm uses 0x90 after a byte as a repeat indicator, followed by a convert binary and hex values to ascii. A count of 0 specifies a byte value of 0x The routine returns the decompressed data, unless data input data ends in an orphaned repeat indicator, in which case the Incomplete exception is raised.
The argument should already be RLE-coded, and have a length divisible by 3 except possibly the last fragment. Compute a bit CRC value of datastarting with an initial crc and returning the result. This CRC is used in the binhex4 format. Compute CRC, the bit checksum of data, starting with an initial crc. This is consistent with the ZIP file checksum. Since convert binary and hex values to ascii algorithm is designed for use as a checksum algorithm, it is not suitable for use as a general hash algorithm.
If convert binary and hex values to ascii are only using the checksum in packed binary format this is not necessary as the return value is the correct 32bit binary representation regardless of sign. Changed in version 2. In the past the value would be signed on some platforms and unsigned on others. Changed in version 3. Return the hexadecimal representation of the binary data. Every byte of data is converted into the corresponding 2-digit hex representation.
The resulting string is therefore twice as long as the length of data. Return the binary data represented by the hexadecimal string hexstr. Exception raised on incomplete data. These are usually not programming errors, but may be handled by reading a little more data and trying again. The binascii module defines the following functions: Module binhex Support for the binhex format used on the Macintosh. Module uu Support for UU encoding used on Unix.
The Python Software Foundation is a non-profit corporation. Last updated on Feb 03, Created using Sphinx 1.
Theory is of course you will recoup your loss, but only works if the trade is placed when the item moves in the correct direction. Stick to 10 as a maximum of your account but 5 is probably better or less when starting. If a trade looses stick to your 5 dont chase it, 1 loss and 2 wins equates to a positive balance. Take the time an see why it lost, how was it miss read. Trade indicators, that pretty bar chart that says 34puts, 66 calls is only showing where the money is going generally, doesnt indicate whether they are long term or short term trades just the pool of money.